Includes: GERTP Table: MB1 - Mel Rpt/Bend 1

The following table shows the default GE Real-Time Parameters in an initialized RTC model. It's very rare that any of the parameters with slider/switch assignments are ever changed for a particular GE based on this RTC model. However a KARMA Designer will quite often change some of the non-assigned parameters, particularly in the 17-32 range, so some of the parameters that you see in a specific GE using this RTC model might not exactly match the following table.

RTC Model: MB1 - Mel Rpt/Bend 1 - 32 GE RTP
No. GE RT Parameter Min Max Value Assign
1 Rhythm: Swing% 0~100,-200,+200 Min:+0000 Max:+0102 Val:+0000 - - - -

[table in progress]

2 Repeat: Rhythm Min:+0000 Max:+0024 Val:+0008 Slider 4

[table in progress]

3 Repeat: Repetitions Min:+0000 Max:+0101 Val:+0020 Slider 5

[table in progress]

4 Repeat: Initial Velocity Min:-0126 Max:+0000 Val:-0016 Slider 6

[table in progress]

5 Repeat: Decay Min:-0126 Max:+0006 Val:-0016 Slider 7

[table in progress]

6 Repeat: Transpose Min:-0024 Max:+0025 Ctr:+0000 Slider 8

[table in progress]

7 Repeat: Chord Shift Min:+0000 Max:+0001 Val:+0001 - - - -

[table in progress]

8 Repeat: Stop Mode Min:+0000 Max:+0001 Val:+0001 - - - -

[table in progress]

9 Repeat: Rebound Mode Min:+0001 Max:+0002 Val:+0002 - - - -

[table in progress]

10 Repeat: Range Bottom (Abs) Min:+0024 Max:+0096 Val:+0036 - - - -

[table in progress]

11 Repeat: Range Top (Abs) Min:+0048 Max:+0127 Val:+0096 - - - -

[table in progress]

12 Repeat: Range Bottom (Rel) Min:-0063 Max:+0064 Ctr:+0000 - - - -

[table in progress]

13 Repeat: Range Top (Rel) Min:+0000 Max:+0064 Val:+0024 - - - -

[table in progress]

14 Repeat: Range Mode Min:+0000 Max:+0001 Val:+0000 - - - -

[table in progress]

15 Repeat: Key Mode (RT) Min:+0000 Max:+0001 - - - - Switch 8

[table in progress]

16 Repeat: Vel. Range Bottom Min:+0001 Max:+0110 - - - - Switch 7

[table in progress]

17 Repeat: Chord Quantize (RT) Min:+0000 Max:+0001 Val:+0000 - - - -

[table in progress]

18 Repeat: Duration Value (RT) Min:+0002 Max:+0250 Val:+0250 Slider 3

[table in progress]

19 Repeat: Duration Mode (RT) Min:+0004 Max:+0001 - - - - Slider SW 3

[table in progress]

20 Bend: On/Off Min:+0000 Max:+0001 - - - - Switch 1

[table in progress]

21 Bend: Amount Min:-0012 Max:+0012 - - - - Switch 2

[table in progress]

22 Bend: Alternation Min:+0000 Max:+0001 Val:+0000 - - - -

[table in progress]

23 Bend: Shape Min:+0000 Max:+0001 - - - - Switch 4

[table in progress]

24 Bend: Step Mode Min:+0000 Max:+0012 Val:+0000 - - - -

[table in progress]

25 Bend: Length Min:+0000 Max:+0023 Ctr:+0013 Slider 1

[table in progress]

26 Bend: Start % Min:+0000 Max:+0050 Val:+0050 Slider 2

[table in progress]

27 Bend: End % Min:+0050 Max:+0100 Val:+0050 Slider 2

[table in progress]

28 Bend: Width % Min:+0000 Max:+0100 Val:+0100 Slider 2

[table in progress]

29 Bend: Direction (RT) Min:+0000 Max:+0001 - - - - Switch 3

[table in progress]

30 Bend: Key Mode (RT) Min:+0000 Max:+0001 - - - - Switch 6

[table in progress]

31 Bend: Rel. Delay Length (RT) Min:+0000 Max:+0010 - - - - Switch 6

[table in progress]

32 Bend: Vel. Range Bottom (RT) Min:+0001 Max:+0110 - - - - Switch 5

[table in progress]

Unless otherwise stated, the content of this page is licensed under Creative Commons Attribution-NonCommercial-NoDerivs 3.0 License